An Introduction to UV-C LED Lighting for Germicidal, Sterilization and Disinfection Applications
Ultraviolet lights have shown great promise in providing effective sterilization and disinfection of surfaces. Not all UV lights are effective for sterilization and disinfection purposes, however. In this article, we'll go over the various types of UV lamps as well as technologies and wavelength ranges that do and do not effectively work for UVGI (ultraviolet germicidal irradiance).
Different Types of Ultraviolet
Just like visible light, ultraviolet is made up of a wide range of wavelengths on a spectrum, and this requires us to be more specific when we discuss different ultraviolet lights. The specification we need to look at is the wavelength, measured in nanometers (nm). Ultraviolet wavelengths can range from 100 nm to 400 nm, which is almost as wide as the entire visible spectrum (400 nm to 800 nm). The same way there are many types of visible light (630 nm = red, 530 nm = green, 460 nm = blue, etc) that depend on their wavelengths, there are many types of ultraviolet that have different characteristics depending on their wavelength.
Ultraviolet energy is categorized by wavelength, and is broken down into the following types:
- UV-A: 315-400 nm
- UV-B: 280-315 nm
- UV-C: 100-280 nm
Perhaps the most common type of ultraviolet lamp you may come across is one that emits in the UV-A region of the spectrum. UV-A radiation is invisible until certain materials fluoresce, or "glow." Many fluorescent paints, minerals, and "blacklight" effect products are sensitive to UV-A wavelength energy. UV-A radiation is the weakest form of ultraviolet energy, but caution must be taken as it is nonetheless harmful under excessive exposure, especially as it is invisible.
Many UV LED products emit in the UV-A range, and are commonly referred to as blacklights. They are used across a variety of applications such as fluorescence, curing and blacklight artwork. Although these products are certainly considered ultraviolet, their wavelengths are far too long at 360 nanometers or higher. These wavelengths, have not been shown to be effective for germicidal or sterilization applications and therefore should not be used.
UV-B radiation has a shorter wavelength than UV-A radiation, and is generally stronger than UV-A. While both UV-A and UV-B are present in natural sunlight, UV-B is the primary wavelength that causes sunburn and skin cancer. Despite its stronger energy potential, UV-B's ability to sterilize and inactivate viruses, bacteria and molds has been shown to be quite limited.
Instead, to successfully implement an ultraviolet sterilization system using LEDs, you will need to specifically look for UV LEDs that emit in the UV-C portion of the spectrum. This is due to the way in which the DNA and RNA molecules react to these wavelengths, rendering the pathogens sterile and unable to reproduce. Therefore, you will want to have a UV light which specifically has a UV-C wavelength calibrated for germicidal applications.
Why Does it Have to be UV-C?
The reason it is absolutely critical that the correct wavelength of ultraviolet is used for germicidal applications is due to the mechanism through which the pathogen becomes deactivated. DNA and RNA are the building blocks of life, including microscopic organisms and pathogens such as viruses, bacteria and molds. Without this genetic material, pathogens are unable to reproduce, eventually leading to the death of an infectious colony.
DNA molecules are made up of nucleic acids called adenine (A), cytosine (C), guanine (G), and thymine (T). (Uracil replaces thymine in RNA). Robust and repeated research has found that when thymine is exposed to specific ultraviolet wavelengths, the molecule absorbs the ultraviolet energy and undergoes a chemical bond change. This change in chemical bond configuration results in an alteration of the DNA sequence, which prevents the pathogen from reproducing.
Thymine (and Uracil) have an absorption spectra that are especially sensitive at wavelengths at or near 265 nanometers. At wavelengths longer than 300 nanometers, there is almost no absorption. The absorption spectra are shown in the shaded white curves in the chart below.
As the spectral chart shows, thymine and uracil are not reactive to UV-A wavelengths, and most UV-B wavelengths except those at or below 300 nanometers.
Are we certain that longer wavelengths such as UV-A do not work?
Because UV-A and longer wavelength UV products are generally more available, many people will ask if their fluorescent blacklight will work for germicidal applications. According to UVGI theory, these longer wavelength products will fail to cause a breakdown in the DNA sequence, and will not result in effective sterilization.
Research has shown that there are other photochemical processes that may occur with UV-A wavelength exposure, such as the creation of free radicals, which can contribute to inactivation. Other mechanisms, such as heat generation upon exposure, can also be potential avenues through which non UV-C radiation can result in disinfection. In general, however, research has shown that UV-C is the only wavelength band which can reliably and consistently inactivate a wide range of viruses, bacteria and molds.
Chart showing DNA structure disruption before & After UV exposure
Principles of UVC Disinfection
UV-C Exposure is a proven disinfection technique validated through a century of scientific experiments and actual medical practice. Ultraviolet light with a wavelength of less than carry enough energy to cause a break in the chemical bonds in the DNA and RNA basesof Thymine and Uracil. This disrupts the replication process and rendersthe organism harmless. Since the overwhelming majority of the pathogens on earth require DNA or RNA to replicate, UV-C is a disinfection technique that is universally effective against Bacteria, Virus, Mold Spores and evensmall parasites.
UV-C disinfection is fast acting, does not leave behind toxic residue, foulsmellor bad taste and ther is no worries about drug resistance developing.
UV Air Purifiers in New Orleans, Mandeville, Slidell, LA and Surrounding Areas
UV Air Purifiers & Ultra Violet Air Purification Services In New Orleans, Mandeville, Slidell, Sun, Bush, Folsom, Gretna, Harvey, Elmwood, Goodbee, Hammond, Harahan, Lacombe, Loranger, Metairie, St. Rose, Chalmette, Covington, Eden Isle, Jefferson, Terrytown, Timberlane, Pearl River, Ponchatoula, River Ridge, Madisonville, Old Metairie, Abita Springs, Woodmere, Kenner, Louisiana, and Surrounding Areas
When you install a top-quality ultraviolet air purifier from Mega Air, Inc. for your New Orleans, LA home’s air purification needs, you’ll receive a UV air purifier that will both eliminate mold and bacteria and kill the organisms that can grow in your home cooling system. Installing a UV air purifier from us will help you enjoy improved indoor air quality and better performance from your home’s cooling system.
Count on Mega Air, Inc. for the UV air purification needs of your New Orleans, LA home.
By selecting Mega Air, Inc. to assist you with the indoor air quality concerns of your New Orleans, LA home, you’re choosing a company that has worked hard to help people stay comfortable for more than 38 years. We will be happy to show you how choosing a germicidal UV purifier can benefit you and your family. Our technicians are experts in the field of home comfort who have been specially trained to professionally install your new UV air purification system.
At Mega Air, Inc., our ultimate goal is top comfort for you and your family, as well as energy savings for your household. When you need ultraviolet air purification for your New Orleans, LA area home, rely on Mega Air, Inc. to meet your needs. Call us today for friendly, professional assistance with your indoor air quality needs. contact us at 985-641-1299
Mega Air, Inc. is a full-service air quality contractor.